Error codes – Πλυντήρια ρούχων DAEWOO

Κωδικοί βλάβης για DAEWOO

IE
Water inlet error – washing machine failed to fill
The fault code is displayed, if the washing machine does not detect any incoming water.
·         Check wiring to water inlet valve
·         Check water valve
·         Check drain pump
·         Check pressure switch
·         Check PCB
OE
Water has failed to drain from the washing machine
This fault code is displayed should the washing machine or washer dryer fail to drain water from the tank.
·         Check drain pump
·         Check wiring
·         Check water level sensor
·         Check connections to water valve and PCB
UE
Wash load imbalance detected
The wash load has been detected as an unbalanced load and the washing machine or washer dryer has failed to spin.
·         Sort the laundry load and attempt spin again
LE
Washing machine door opening error
The washing machine or washer dryer door has been detected as open or unlocked.
·         Close the door!
·         Check the door lock switch
·         Check the door latch
·         Check PCB
E2
Overfilling error
The washing machine has detected an overfill situation and the failure code is displayed.
·         Check water inlet valve
·         Check drain pump
·         Check pressure switch or level sensor
E3
Fan motor error detected
On washer dryer models an error has been detected with the dryer fan motor.
·         Check fan motor for obstruction or blockage
·         Check fan motor continuity
·         Check PCB
E9
Pressure sensor error
The washing machine has detected an error with the pressure switch or level sensor
·         Check wiring to level sensor
·         Check level sensor
E5
High voltage error
We’re not quite sure what this one means as the fault code sheet says the following causes this error:
·         Huge noise
·         Spinning with clothing jammed between the drum and gasket
·         PCB failure
E6
EMG Error
Again, your guess is as good as ours on this one as well with the following being listed against the error
·         Huge noise
·         Spinning with clothing jammed between the drum and gasket
·         Motor failure
·         PCB failure
E7
Direction error
This error code is displayed should the motor or drum be detected in moving in the opposite direction it should.
·         Check hall sensor
E8
Washing machine motor error detected
A fault has been detected with the main drive motor.
·         Check motor connection block
·         Abnormal loading condition
H1
Dryer temperature sensor error detected
A fault has been detected with the dryer temperature sensor on washer dryer models.
·         Check connections to dryer sensor
·         Check temperature sensor
H2
Wash temperature sensor error detected
A fault has been detected with the washing thermistor or temperature sensor.
·         Check connections to wash temperature sensor
·         Check temperature sensor
H3
Overheating dryer heater element detected
A fault has been detected with the dryer side heating.
·         Check fan motor is clear and unobstructed
·         Check wiring
·         Check dryer heating sensor
H4
Overheating wash heating element detected
A fault has been detected were the washing machine is overheating on wash.
·         Check water level
·         Check temperature sensor
H6
Wash heating element failure detected
A fault has been detected were the element is not heating.
·         Check wash heating element
·         Check wiring
·         Check thermistor
H7
Dryer heating element failure detected
A fault has been detected with the drying heater element.
·         Check wiring
·         Check dryer heater element
·         Check wiring
·         Check thermistor
H8
Washing heater overheating detected – no water in washing machine
The wash heating element has been detected as working with no water in the washing machine.
·         Check water level
·         Check wiring
·         Check thermistor
·         Check PCB
PEF
Washing machine filter detected as blocked
The machine has detected the drain filter as being blocked
·         Check the drain filter and clear any blockage

 

Συντάκτης: tapavakos

Ψυκτικός

Σχολιάστε

Εισάγετε τα παρακάτω στοιχεία ή επιλέξτε ένα εικονίδιο για να συνδεθείτε:

Λογότυπο WordPress.com

Σχολιάζετε χρησιμοποιώντας τον λογαριασμό WordPress.com. Αποσύνδεση /  Αλλαγή )

Φωτογραφία Google

Σχολιάζετε χρησιμοποιώντας τον λογαριασμό Google. Αποσύνδεση /  Αλλαγή )

Φωτογραφία Twitter

Σχολιάζετε χρησιμοποιώντας τον λογαριασμό Twitter. Αποσύνδεση /  Αλλαγή )

Φωτογραφία Facebook

Σχολιάζετε χρησιμοποιώντας τον λογαριασμό Facebook. Αποσύνδεση /  Αλλαγή )

Σύνδεση με %s