Error codes – Πλυντήρια ρούχων Whirlpool Dreamspace

Whirlpool Dreamspace

FH
Washing machine has failed to fill with water
No water detected entering machine or pressure switch activation not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch activation then the water valves will be turned off and the error code will be displayed.
Press PAUSE/CANCEL twice to clear the error display.
·         If there is water in the washing machine:
o    Make sure that both valves at the water tap or taps are turned on all the way
o    Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
o    Verify inlet valve operation
·         If there is water in the washing machine:
o    Verify Drain pump operation
o    Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
·         Check there is not a siphon problem
·         Check wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
·         Check all hoses for possible leaks
·         Check pressure switch operation
·         Check flow meter operation ***( Normally the FLOW METER)***
·         Check CCU operation
F02
Water failed to drain on time
If the drain time exceeds eight minutes, the water valves are turned off and the F02 error code is displayed.
Press PAUSE/CANCEL twice to clear the display.
·         Check the drain hose and make sure it is not plugged or kinked
·         Check the electrical connections at the pump and make sure the pump is running.
·         Check the drain pump filter for foreign objects
·         If the above does not correct the problem replace the pump
After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.
F05
Water temperature sensor error
If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the F05 error code will be displayed.
·         Check the Water Temperature Sensor, Heating Element and Element Relay
·         Check connections to the Sensor, Heating Element and Relay
F06
Motor tachometer error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.
·         Check wire harness connections between the Drive Motor/Tachometer
·         Check Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
·         Check the Drive Motor
·         Check the MCU
·         Check the Wire Harness
F07
Motor control unit (MCU) error
The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.
·         Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU)
·         Check wiring between the MCU and the Central Control Unit (CCU)
·         Check the MCU
·         Check the Drive Motor
·         Check the Wire Harness
F09
Washing machine has overfilled with water
If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the washing machine to service.
·         Check the drain hose and make sure it is not plugged or kinked
·         Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
·         Check / Clean Drain Pump Filter of foreign objects
·         Check for Drain Pump Failure
·         Check the Inlet Valve for proper shut off
·         Check the Pressure switch for proper operation
F10
Washing machine motor control unit (MCU) overheated
Motor Control Unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an F10 will be displayed.
·         Check for Proper Installation
·         Ensure the washing machine is not located near a source of heat and has proper ventilation.
·         Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
·         Check the Drive system for any worn or failed components
·         Check MCU
·         Check Motor
F11
Communnications error between control cards
Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.
·         Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
·         Check the Drive system for any worn or failed components
·         Check MCU
·         Check CCU
·         Check Motor
·         Check Wire Harness
F13
Dispenser circuit error
If the dispenser motor is not able to be driven to it’s proper position.
·         Check mechanical linkage from dispenser motor to the top of the dispenser.
·         Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)
·         Check Dispenser Motor
F14
EEPROM error
The Central Control Unit (CCU) receives it’s data from an EEPROM onboard the CCU. If there is an error reading this data it will cause this error.
·         A power glitch may cause this error
·         Try unplugging the Unit for two minutes to see if that fixes the error
·         Check CCU
F15
Motor control unit error
If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode.
·         Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
·         Check Drive belt
·         Check MCU
·         Check Motor
·         Check Wire Harness
Sud
Suds lock detected – Washing machine overdosed
The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. If “Sud” is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.
·         Check the drain hose and make sure it is not plugged or kinked
·         Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
·         Check / Clean Drain Pump Filter of foreign objects
·         Check Drain Pump
·         Check the Pressure Switch
·         Check CCU
If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. This should clear the unit of the excess detergent.
FdL
Door lock error when locking the washing machine door
A door lock error occurs if the door cannot be locked. It will try to lock it 6 times before displaying the error.
·         Door Lock Mechanism broken or removed from the door
·         Check Door Lock/Switch Assembly
·         Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
·         Door Lock/Switch Assembly Failure

 

FdU
Door lock error when unlocking the washing machine door
A Door unlock error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error.
·         Door Lock Mechanism broken.
·         Check Door Lock/Switch Assembly for foreign objects
·         Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
·         Door Lock/Switch Assembly Failure

Author: tapavakos

Ψυκτικός

Leave a Reply