Zanussi με “EWM1000plus”, “EWM2000evo” και “EWM3000new” πλακέτα
Της Zanussi οι κωδικοί σφαλμάτων είναι ίδιοι σε πολλές συσκευές της Electrolux Group όπως: AEG, Arthur Martin, Tricity Bendix, John Lewis.
Πώς να διαβάσετε τον κωδικό βλάβης σε συσκευές Zanussi που δεν χρησιμοποιούν display:
- Απενεργοποιήστε την συσκευή
- Πατήστε και κρατήστε πατημένα τα κουμπιά START/PAUSE και ένα από τα κουμπιά επιλογής ταυτόχρονα
- Κρατώντας πατημένα τα 2 κουμπιά γυρίστε δεξιόστροφα τον επιλογέα προγράμματος μία θέση
- Συνεχίστε να πατάτε τα 2 κουμπιά έως ότου η ενδεικτική λυχνία αρχίσει να αναβοσβήνει τουλάχιστον 2 δευτερόλεπτα
- Γυρίζοντας τώρα τον επιλογέα δεξιόστροφα ενεργοποιεί το διαγνωστικό των επιμέρους προγραμμάτων
Εμφάνιση κωδικού σφάλματος:
Ο συναγερμός εμφανίζεται από μια επαναλαμβανόμενη ακολουθία που αναβοσβήνει από τα δύο LEDs (0,4 δευτερόλεπτα ΟΝ, 0,4 δευτερόλεπτα OFF, με παύση 2,5 δευτερολέπτων μεταξύ κάθε ακολουθίας).
Ο βομβητής (αν υπάρχει) ακούγεται μια σειρά από «μπιπ» συνχρονισμένος με το αναβόσβημα των LED.
«Το Τέλος του κύκλου” υποδηλώνει το πρώτο ψηφίο του κωδικού βλάβης
“Έναρξη Παύση” υποδηλώνει το δεύτερο ψηφίο του κωδικού βλάβης
Δείτε το παράδειγμα παρακάτω για να καταλάβετε είναι απλό!
Αυτά τα δύο LED υπάρχουν σε όλα τα μοντέλα.
Σημειώσεις:
Το πρώτο γράμμα του κωδικού συναγερμού “E” (Error) αγνοείται καθώς είναι ίδιο για όλους τους κωδικούς συναγερμού.
Οι κωδικοί βλάβης εκφράζονται σε δεκαεξαδική μορφή. Με άλλα λόγια:
Το Α αντιπροσωπεύει 10 φορές να αναβοσβήνει
Το Β αντιπροσωπεύει 11 φορές να αναβοσβήνει
Το F αντιπροσωπεύει 15 φορές να αναβοσβήνει
Τα σφάλματα ρύθμισης παραμέτρων που εμφανίζονται από το αναβόσβημα όλων των LEDs σημαίνει η πλακέτα πρέπει να επαναπρογραμματιστεί ή να αντικατασταθεί.
Παράδειγμα ενός κωδικού σφάλματος:
Παράδειγμα: Σφάλμα E43 (προβλήματα με την ασφάλεια της πόρτας) θα πρέπει να εμφανίζεται ως εξής:
Αναβοσβήνει τέσσερις φορές το “τέλος του κύκλου» αναφέρει το πρώτο ψηφίο “4” του κώδικα E43
Τρεις αναλαμπές του “Έναρξη Παύση” αναφέρει το δεύτερο ψηφίο “3” του κώδικα E43
Τα περισσότερα μοντέλα με απλό control και display (EWM1000). Η συγκεκριμένη πλακέτα χρησιμοποιείται ευρέως σε AEG συσκευές.
E11
|
Difficulty in filling during wash phase
|
This is usually your basic filling error so the usual should be checked, that the water supply is switched on and then onto the water fill valves.
E13
|
Water leakage detected
|
This is only applicable where a leak detection system is fitted.
E21
|
Difficulties in draining, drain error
|
Basic drain error, check the drain pump filter is clear and also the drain pump is actually working.
E23
|
Malfunction of drain pump triac
|
This refers to the triac that controls the pump function on the main controller.
E24
|
Sensing circuit of the component (triac) that controls the drain pump faulty
|
As above.
E33
|
Incongruous between closure of anti-boiling and 1st level contacts of pressure switch
|
This is a pressure switch or sensor fault and we would not recommend you attempt to DIY this fault.
E35
|
Water level too high
|
Again, water pressure system fault and again, we wouldn’t consider this to be a DIY repair.
E36
|
Sensing circuit of anti-boiling pressure switch faulty
|
As above.
E37
|
Sensing circuit of 1st level pressure switch faulty
|
As above
E39
|
HV sensing circuit of anti-overflow pressure switch faulty
|
As Above
E40
|
Door open, door interlock, wiring or main PCB
|
Usually a door lock that’s faulty.
E41
|
Door open
|
Close the door!
E42
|
Problems with aperture of the door
|
Pretty much the same as E40 and E41 fault codes.
E43
|
Problems with the triac which actions the door interlock
|
Again, this refers to the triac on the electronic controller and you should seek an engineer as it is not a DIY repair.
E44
|
Door closure sensing circuit faulty
|
As E40, E41 and E42.
E45
|
Problems with the sensing circuit of the triac that actions the door interlock
|
As E43.
E51
|
Motor power triac short-circuited
|
Yet again, this refers to the triac on the electronic controller and not a DIY job.
E52
|
No signal from the motor tachometric generator
|
Tacho coil on the motor is most probably faulty. This coil reads a magnet as the motor turns to detect the speed that the motor is spinning at and this in turn allows the electronic controller to set the motor to revolve at different speeds for the various program options.
E53
|
Problems with the sensing circuit of the triac which powers the motor
|
Another one that is a fault being reported on the electronic controller and not a DIY repair.
E54
|
Motor relay contacts sticking
|
As above.
E61
|
Insufficient heating during washing
|
Usually a heater failure but possibly the thermostat or NTC temperature sensor or wiring to either.
E62
|
Overheating during washing
|
As above only the heater will likely be okay.
E66
|
The contacts of the heating element power relay are always closed
|
Another one that requires an engineer, not a DIY repair.
E71
|
NTC washing sensor faulty
|
Self explanatory but do also check the wiring to the temperature probe.
E82
|
Error in reading the RESET/OFF position of the programme selector
|
Another non-DIY one, you will need an engineer.
E83
|
Error in reading the programme selector code
|
As above.
E93
|
Incorrect machine configuration
|
As above.
E94
|
Incorrect configuration of washing cycle
|
As above.
E95
|
Communications error between microprocessor and the EEPROM
|
As above.
E96
|
In congruence between control panel version and configuration data
|
As above.
E97
|
In congruence between selector version and configuration data
|
As above.
EA1
|
Drum positioning system (DSP) faulty (top-loaders only)
|
Not really used in the UK, more for European top loading models.
EB1
|
Incorrect mains frequency
|
Check mains supply, you may require an electrician to do this for you.
EB2
|
Mains voltage too high
|
Check mains supply, you may require an electrician to do this for you.
EB3
|
Mains voltage too low
|
Check mains supply, you may require an electrician to do this for you.